What is going on here? (apart from not much at all...)

Yes, I'm still here.

Shame on me for not posting for such a long time.
The long silence is not without reason of course, as I haven't been very active modelling-wise.

Not that there aren't enough projects on my mind (or started kits on my workbench for that matter).
Just haven't really felt the drive to build something, especially after the clear paint job on my Ferrari went down the drain in the worst kind of way...
The long and hot summer didn't help either with the temperatures on the attic rising to inhuman levels. Just sitting at my PC had me breaking a sweat, without moving even the tiniest muscle...

Anyway. After changing jobs recently I happen to have some more spare time on my hands courtesy of shorter travel time and better work hours.
This gives me some welcome extra time and actually makes me feel more relaxed.
To the point that I actually am getting a little fired up to start building and painting again.

After visiting KMK Scaleworld (a post on that will apear shortly) last weekend I must say that I really am looking forward to get moving again.
And it's about time too I'd say.

I promise that the next post will actually show some models (although not made by me...) and will be up before next week.

Stay tuned.

Comments

Citroën Xsara WRC - Francois Duval, ADAC Rallye Deutschland 2007 (part 5)

As promised in the previous part in this update I'll show what I changed on the roll cage. The roll cage as included in the kit is far from complete. When looking at on-board footage and reference images found on the internet the roll cage needs some extra tubing added. Over the years the roll cage of the Xsara WRC has had several variants as I've noticed studying my reference images. Which isn't that strange as the crash test and safety regulations have changed over the years. The reference images I have of the specific chassis (#28) which Duval raced during the 2007 ADAC Rallye Deutschland are sadly inconclusive about which version of the roll cage was fitted. Which means that the adaptations I made are at best a good "guesstimate"... As long as it looks and feels right, it is right I guess... I used Evergreen styrene rod of 1.6 mm in diameter for the added sections for the rollcage. The added sections are highlighted in the images below. Another section I...

Benetton Ford B190B, F1 season 1991 (part 6)

After preparing all the sub assemblies and parts I gave them a good wash with lukewarm water with some dish washing soap. While the parts were drying I decanted Tamiya surface primer (white and grey) into some paint jars. All the parts received a grey primer coat to check for blemishes or spots that need to be reworked. After everything is checked the wings and body will be primed with the white surface primer. After the grey primer, this is how everything looks. Apart from the front wings and the rear wing, everything looks ready for a splash of color. The front wings need some extra work filling and sanding to get rid of the ejector pin marks. The ejector pin marks on the rear wing are hardly visible anymore. Only a few short shot spots on the back of the rear wing need some attention. After sanding, the front wings, rear wing and the body got a coat of white primer in preparation for the color. In the meantime I already painted the suspension, cockpit and engine/g...

Benetton Ford B190B, F1 season 1991 (part 5)

Well. I can hardly believe how long I've been silent here on this blog. Not counting the two show reports I posted earlier this week, the last posting here being from November 2021... But, since I went from a 5 to a 4 day work week at the beginning of this year, there is finally some more spare time to spend. Oh, and a good cleaning of the modelling "cave" did also help in motivating me to dive into the cellar and do some building again. To start a (fingers crossed) longer stint of modelling activities, I decided to (finally) continue with this particular kit. It's been lying around for almost 10 years, so you can say it's desperately in need of some attention. Luckily all parts are still accounted for as I had the parts nicely packed away (for a change). Upon inspecting my work I couldn't quite look past a few things that weren't so neatly done. Especially the engine/gearbox and rear wing assemblies were a bit wanting. Also, upon cross-checking ...

Axel's corner

Search This Blog