Ford Focus WRC 02, Rally Oltrepò Pavese 2007 (part 3)

Since I first decided to close the wheelarches I have since backtracked on that decision and removed the attached pieces of styrene.
I couldn't get it to work properly and decided I'd take a closer look at how big the gaps would be with a thorough dryfit of the model.

There are still some gaps visible and I haven't yet decided how I'm going to tackle them.

In the meantime I've been working on the bonnet of the car.
The instructions from Renaissance for adding the PE parts to the resin bonnet aren't entirely clear to me, but after studying some reference images of the real car I was pretty sure that the PE grilles needed to be glued on the outside (on the top) of the bonnet.

A first dryfit showed that the PE and resin parts didn't quite match, so I had do do some sanding and puttying to get it all to fit properly.

More next time.

Comments

Citroën Xsara WRC - Francois Duval, ADAC Rallye Deutschland 2007 (part 6)

Welcome to the next part of this build report. I left you last time (or should I say long, long ago...) with the images of the primed body, floor and roll cage, showing that there was some work to do to get everything ready for some color. In this update I will show you how far I got with these parts. I'll start with the body and floor. Sanding everything back turned out to be quite a bit of work. And of course there were several areas still in need of attention. Especially around the wheel arches there was a lot of additional work left. Luckily, with the car in tarmac setup, there's not much room left to see the remaining rough spots that have survived the clean up process... Which leads me to the conclusion that I could have cut some corners in this particular area by only cleaning up the most visible sections. It's a good lesson to check beforehand what is actually visible when the car is built together. I'll definitely be cutting some corners for the other two ...

Citroën Xsara WRC - Francois Duval, ADAC Rallye Deutschland 2007 (part 5)

As promised in the previous part in this update I'll show what I changed on the roll cage. The roll cage as included in the kit is far from complete. When looking at on-board footage and reference images found on the internet the roll cage needs some extra tubing added. Over the years the roll cage of the Xsara WRC has had several variants as I've noticed studying my reference images. Which isn't that strange as the crash test and safety regulations have changed over the years. The reference images I have of the specific chassis (#28) which Duval raced during the 2007 ADAC Rallye Deutschland are sadly inconclusive about which version of the roll cage was fitted. Which means that the adaptations I made are at best a good "guesstimate"... As long as it looks and feels right, it is right I guess... I used Evergreen styrene rod of 1.6 mm in diameter for the added sections for the rollcage. The added sections are highlighted in the images below. Another section I...

Benetton Ford B190B, F1 season 1991 (part 5)

Well. I can hardly believe how long I've been silent here on this blog. Not counting the two show reports I posted earlier this week, the last posting here being from November 2021... But, since I went from a 5 to a 4 day work week at the beginning of this year, there is finally some more spare time to spend. Oh, and a good cleaning of the modelling "cave" did also help in motivating me to dive into the cellar and do some building again. To start a (fingers crossed) longer stint of modelling activities, I decided to (finally) continue with this particular kit. It's been lying around for almost 10 years, so you can say it's desperately in need of some attention. Luckily all parts are still accounted for as I had the parts nicely packed away (for a change). Upon inspecting my work I couldn't quite look past a few things that weren't so neatly done. Especially the engine/gearbox and rear wing assemblies were a bit wanting. Also, upon cross-checking ...

Axel's corner

Search This Blog